White-Rodgers Drum Humidifier with Humidistat

Skuttle Current Sensing Relay A50

• Sensing Relay

The relay is clamped on to the blower wire and has an internal switch that closes when the blower receives current. The blower voltage can be 120v or 240v, only the is amperage important. The internal switch is electronic and can only switch on or off 24 volts, such as any 24 vac humidifier.

Skuttle Automatic Flushing Timer

• Flushing Timer

The flushing timer drains the humidifier water pan allowing it to refill with fresh clean water. The timer is set to drain the water every 12 hours. Flushing the humidifer keeps the humidifier clean of stagnant water and mineral deposits from accumulating.

White-Rogers HDT2600 Versus Honeywell 120

The White-Rodgers HDT2600 is the same as the Honeywell HE120A. Skuttle manufactures the HDT2600 for White-Rodgers as well as the Honeywell.

All items included with the HE120A are also included with the HDT2600. As well as all internal parts are the same.

White-Rogers HDT2600 Versus Skuttle 190

The White-Rodgers HDT2600 is the same as the Skuttle 190. Skuttle manufactures the HDT2600 for White-Rodgers and applies their logo.

All items included with the Skuttle 190 are also included with the HDT2600. As well as all internal parts are the same.

By-Pass Versus Power Humidifier

The term By-Pass or Power refers to the driving force behind the air flow. The Power humidifier (aka Fan Power) uses a fan to draw the air thru the humidifier. The ByPass humidifier uses a 6" diameter duct that connects the supply to the return duct.

In the ByPass configuration the air leaving the furnace is routed back to the supply. The warm air leaving the furnace takes this short-cut of least resistance and bypasses the long trip down the duct work, in to the house, and back through the return. The ByPass is the 6" round duct work shown to the left. During the the hot humid A/C season the ByPass duct should be closed with a butterfly valve since the air flow through the humidifier would not be needed.

The Power humidifier uses a fan to draw air in from the duct and through the humidifier and exhausts back out in to the duct. The air is drawn in through duct at the center of the humidifier and back out in to the duct at the sides. The power humidifier should be mounted in vertical warm air flow.

The HE225 and HE265 are ByPass humidifiers. The HE365 is a fan powered humidifier.

Manual Versus Automatic Humidistat

The indoor humidity level needs to be set based on the outside temperature. This is to prevent water from running down the windows. The cool air near the windows can not hold the humidity and water will condense on the glass. To prevent this condensation, the indoor humidity level is sacrificed by lowering the humidistat.

An automatic humidistat (Aprilaire 60 or Honeywell H6062A) adjusts the humidity by using an outside temperature sensor.

Manual humidistat as used in earlier humidifiers (Model 4655 or H8908b1010) requires adjusting the relative humidity based on the outside temperature. A manual humidistat needs to be set back as the season gets colder. The chart below shows the humidity setting for a range of outside temperatures.

When The Outdoor Temperature is	This Relative Humidity Should Be Maintained
+40°F	45%
+30°	40%
+20°	35%
+10°	30%
0°	25%
-10°	20%
-20°	15%

• Model 60 Manual
• Humidity Information

White-Rogers Warranty

• HDT2600 Warranty

The White-Rodgers warranty for our new HFT2600 humidifier is one year. Our customers simply ship us the defective part. We inspect and test and confirm defective. We then ship back a brand new part.

The problem with humidifiers is typically due to water quality. Parts will corrode or freeze up with calcium and lime deposits. The mineral deposits from hard water will contain salt that can corrode the motor. Water filtration and treatment is the solution. The warranty does not cover problems with corrosion.